Aiwa MP3 Player MM VX200 User Manual

OPERATING INSTRUCTIONS  
INSTRUCCIONES DE MANEJO  
MODE D’EMPLOI  
MM-VX200  
MP3 PLAYER  
REPRODUCTOR MP3  
ENGLISH  
ESPAÑOL  
FRANÇAIS  
OWNER’S RECORD  
For your convenience, record the  
model number (you will find it on  
the rear of your set) and the serial  
number (you will find it in the  
cassette holder of your set) in the  
space provided below.  
Pleasereferthemwhenyoucontact  
yourAiwadealerincaseofdifficulty.  
Model No.  
Serial No.  
For assistance and information,  
call toll free 1-800-BUY-AIWA.  
(United States and Puerto Rico)  
8A-HZ1-911-01  
000721AYO-O-K  
Printed in Korea  
 
CONTENTS  
2
Chapter 1  
PREPARATION BEFORE USE  
Thefollowingaresuppliedwiththisplayer.  
Check to be sure all the items are in the  
package.  
1 SYSTEM REQUIREMENTS . . . . . 3  
2 CONTENTS . . . . . . . . . . . . . . . . . 3  
3 PRECAUTIONS . . . . . . . . . . . . . . 4  
4 INSERTING A BATTERY . . . . . . . 5  
5 CONNECTING THE PLAYER TO  
YOUR PC . . . . . . . . . . . . . . . . . . . 6  
• Player  
6
SmartMedia-ID INSTALLATION . . . .  
6
• USB cable  
SYSTEM REQUIREMENTS  
1
The VX200 manager software requires  
the following system:  
• Remote control  
• Stereo headphones  
• Windows 98, Windows 98 second  
edition*  
• Pentium 200 MHz MMX or faster  
• 1 available USB Port  
• CD-ROM drive supporting digital audio  
extraction  
• 15MB free hard-disk space (may vary  
depending on the size of the MP3 files  
you wish to use)  
• 32MB RAM  
• Full duplex Sound card and speakers  
• 16-bit color video card  
• Installation CD-ROM  
• 32 MB SmartMedia-ID  
• Carrying case  
*For use only PC systems in which  
Microsoft Windows 98 or Windows 98  
SecondEditionhasbeenpreinstalledby  
the manufacturer.  
• Operating instructions, etc.  
ENGLISH 3  
 
PRECAUTIONS  
3
The following are precautions that you  
shouldalwayskeepinmind. Anyviolation  
ofoneormoreofthefollowingprecautions  
may cause damage and will void the  
4 ENGLISH  
Battery indicator  
INSERTING A BATTERY  
4
The battery indicator on the display  
changes depending on the remaining  
power of the battery.  
An alkaline battery is recommended for  
use with this player.  
Empty  
1 Open the cover of the battery  
compartment.  
Full  
Battery replacement  
Replace the battery when  
battery indicator lights.  
of the  
Note on dry cell battery  
• Make sure that 0 and 9 marks are  
correctly aligned.  
• Topreventtheriskofelectrolyteleakage  
orexplosions,neverrechargethebattery,  
apply heat to it, or take it apart.  
• When not using the battery, remove it to  
prevent needless battery wear.  
• If the liquid leaks out from the battery,  
wipe thoroughly to remove.  
2 Insert a size AA (LR6) alkaline  
battery with the 0 and 9 marks  
correctly aligned, then close the  
cover.  
ENGLISH 5  
 
Connecting an AC adaptor  
CONNECTING THE  
5
TouseonAChousecurrent, contactyour  
nearest Aiwa service personnel and  
purchase an AC adaptor Aiwa AC-D302.  
Connect the AC adaptor:  
1 to the DC 3 V jack of the player  
2 to a wall outlet  
PLAYER TO YOUR PC  
Use the supplied USB cable to connect  
this player to your PC, as follows:  
Connect the series B connector to the  
USB port connector of the player and the  
other plug to the USB port connector of  
your PC.  
AC-D302  
DC3V  
SmartMedia-ID  
INSTALLATION  
Series B  
connector  
6
USB port connector  
BeforeinsertingaSmartMedia-ID,besure  
to turn off the power of the player and  
disconnect the USB plug from the USB  
port connector.  
Supplied USB cable  
Insert the SmartMedia-ID into the slot in  
the correct direction as follows.  
Series A connector  
USB port  
If a plug is already connected to the USB  
port connector of your PC, disconnect it  
before connecting this player.  
Do not disconnect the USB plug during  
downloading or uploading the files to  
prevent the error of your PC.  
6 ENGLISH  
 
To eject the SmartMedia-ID  
Slide the EJECT switch as follows.  
Use for data storage  
Withupto64MBmemory,including32MB  
in the SmartMedia-ID, you can store not  
only MP3 files but also any data files such  
as doc, gif, txt, bmp, wav, etc. files, as  
long as no file is larger than 32MB.  
Supplied label for SmartMedia-ID  
contact area  
write protect area  
index area  
You can paste the supplied protecting  
label on the write protect area on the  
SmartMedia-ID.  
Donotpasteanylabelonthecontactarea  
on the SmartMedia-ID.  
Note  
InserttheSmartMedia-IDcompletelyinto  
the slot. If it is not inserted completely,  
VX200 Manager will not recognize the  
data in the SmartMedia-ID.  
When using a SmartMedia-ID for the  
first time, initialize the SmartMedia-ID  
using the VX200 Manager software.  
The MP3 files in the SmartMedia-ID  
cannot be played back with other player  
bythesecurityofcopyrightconsideration.  
To use a SmartMedia-ID with other  
player, you need to initialize the  
SmartMedia-ID (See page 16).  
ENGLISH 7  
 
INSTALLING THE VX200  
MANAGER SOFTWARE  
1
Chapter 2  
SOFTWARE INSTALLATION  
Before installation, check your system  
matching to the system that you need  
again (see SYSTEM REQUIREMENTS  
in Chapter 1) and quit all application  
software in use.  
VX200 Manager is communication  
software that allows your computer to  
shareinformationwiththeplayer. Inorder  
for the player to work properly, the VX200  
Manager software must be installed  
correctly under Windows 98.  
1 InserttheinstallationCDintoyour  
CD-ROM drive.  
2 Double-clickontheCD-ROMdrive  
icon to open it.  
1 INSTALLING THE VX200  
MANAGER SOFTWARE . . . . . . . . 8  
2 INSTALLING THE USB  
DRIVER . . . . . . . . . . . . . . . . . . . . 10  
3 INSTALLING THE WAVE DRIVER  
(ADPCM Driver) . . . . . . . . . . . . . 10  
4 UNINSTALLING THE VX200  
MANAGER SOFTWARE . . . . . . . 11  
5 UNINSTALLING THE WAVE  
DRIVER (ADPCM Driver) . . . . . . 11  
8 ENGLISH  
 
3 Double-click on the VX200  
Manager folder to open it.  
1In the Welcome! dialog box, click  
on the Next button to continue  
software installation.  
2Ifyouwishtochangethedestination  
folder to a folder other than the  
default folder shown in the dialog  
box, click on the Browse button to  
select the folder to which you wish  
to copy the VX200 Manager  
software files.  
Next, click on the Next button to  
continue installation.  
3You can click on the Back button to  
reconfigure the installation  
information.Tocontinueinstallation,  
click on the Next button to start  
copying the necessary files into the  
installation folder.  
4Wait until files for the VX200  
Manager software are copied.  
5Now, click on the Finish button.  
This completes VX200 Manager  
software setup.  
4 The setup file for the VX200  
Manager software is setup.  
Double-click on setup to start  
installation of VX200 Manager  
software.  
6The VX200 will be created on the  
/Start/Programs/Vx200 menu on  
the Windows menu bar, and a  
VX200 icon will be created on your  
Windows desktop.  
7You can start VX200 Manager by  
either clicking on the VX200 icon or  
clicking on the Vx200 in the Start  
menu.  
ENGLISH 9  
 
1 InserttheinstallationCDintoyour  
CD-ROM drive.  
INSTALLING THE USB  
DRIVER  
2
2 Double-clickontheCD-ROMdrive  
icon to open it.  
If the USB driver is not installed into your  
PC, youcannotdownloadtheMP3filesto  
the player.  
3 Double-click on the ADPCM  
Drivers folder to open it.  
To install the USB driver, connect the  
player with the supplied USB cable and  
insert the supplied CD-ROM into the CD-  
ROM drive of your PC.  
4 Double-click on ADPCM Driver to  
start installation.  
1In the Welcome! dialog box, click  
on the Next button to continue  
software installation.  
1 Click “Next” on the “Add New  
Hardware Wizard.”  
2Ifyouwishtochangethedestination  
folder to a folder other than the  
default folder shown in the dialog  
box, click on the Browse button to  
select the folder to which you wish  
to copy the ADPCM Driver files.  
Now, click on the Next button to  
continue installation.  
3You can click on the Back button to  
reconfigure the installation  
information.Tocontinueinstallation,  
click on the Next button to start  
copying the necessary files into the  
installation folder.  
4Waituntilthenecessaryfilesforthe  
ADPCM Driver have been copied.  
5Now, click on the Finish button.  
This completes ADPCM Driver  
setup.  
6The Uninstall ADPCM Drivers item  
will be created on the /Start/  
Programs/ADPCMDriversmenuon  
the Windows menu bar.  
2 Select “Search for best driver for  
your device” clicking the button  
of upper side and click “Next”.  
3 Check CD-ROM drive and click  
“Next”.  
4 Click “Next” according to the  
message.  
5 AfterinstallationoftheUSBdriver  
for MM-VX200, click “Finish”.  
INSTALLING THE WAVE  
DRIVER (ADPCM Driver)  
3
You do not need to install this ADPCM  
Wave Driver if you have already installed  
theVX200Managersoftwareasdescribed  
in the above section.  
The ADPCM Driver lets you play WAV  
files converted from voice files you have  
recorded using built-in microphone of  
the player.  
If you wish to send your voice recorded  
as WAV files to someone who does not  
have an MM-VX200 player, that person  
will have to install the ADPCM Wave  
Driver as described below.  
If you need to install only the ADPCM  
Wave Driver, proceed as follows:  
10 ENGLISH  
 
UNINSTALLING THE VX200  
MANAGER SOFTWARE  
4
TouninstalltheVX200Managersoftware,  
choose the /Start/Programs/Vx200/  
Uninstall item from the Windows menu  
bar. This will remove all VX200 files and  
the VX200 folder.  
UNINSTALLING THE  
WAVE DRIVER (ADPCM  
Driver)  
5
If you wish to uninstall the ADPCM Driver  
from your system, choose the /Start/  
Programs/ADPCM Drivers/Uninstall  
ADPCM Drivers item from the Windows  
menu bar. This will automatically remove  
the ADPCM Wave Drivers from your PC.  
ENGLISH 11  
 
PREPARING MP3 FILES  
2
Chapter 3  
Before operating VX200 Manager,  
prepare your MP3 file on your PC.  
On the supplied Installation CD, you can  
find RealJukebox Basic (version 1.0) in  
the RealJukebox folder. You can convert  
youraudioCDdatatoMP3datausingthe  
RealJukebox.  
After preparing an MP3 file on your PC,  
download the MP3 file to the player to  
play back the MP3 files with the player  
(see Page 15).  
SOFTWARE OPERATION  
VX200Managerissoftwarethatinteracts  
with the player and a PC. MP3 files and  
datafilescanbedownloadedtothisplayer.  
However, you can upload only data files  
or recorded voice files to the PC.  
1 OPENING VX200 MANAGER. . . 12  
2 PREPARING MP3 FILES . . . . . . 12  
3
OPERATING VX200 MANAGER . . 14  
Note  
Do not install the RealJukebox Basic  
onto a PC in which RealJukebox Plus  
has been already installed. The  
application will be replaced with  
RealJukebox Basic.  
The RealJukebox supplied in the  
installation CD-ROM does not have the  
function to communicate with MM-  
VX200.  
OPENING VX200  
1
MANAGER  
Before you begin, make sure that the  
player is properly connected to the USB  
Port of your PC and the VX200 Manager  
software has been properly installed.  
AIWA Co., Ltd. does not provide  
technical support for the RealJukebox  
software.  
Access the following URL for details on  
operation,support,andotherinformation  
on RealJukebox.  
1 Double-click on the VX200 icon  
on the Windows desktop or  
choose the /Vx200 from the Start  
menu to activate the program.  
12 ENGLISH  
 
AfterinstallingtheRealJukeboxsoftware,  
change the encoding options as follows.  
ENGLISH 13  
 
OPERATING VX200 MANAGER  
3
1
2 3 4 5 6 7 8 9 10 11 12  
13 14 15 16  
17  
18  
19  
20  
1 Option button  
2 Firmware button  
The Option button brings up the Setup  
menu that allows you to specify the path  
for an MP3 player on your PC. You can  
alsoaccesstheSetupdialogboxfromthe  
Tools/Option menu.  
You need not use this button for usual  
operation. This button has a function for  
reprogramming the firmware. Aiwa will  
provide the updated firmware and the  
usage information for this button on the  
following URL when it is required.  
Click the Browse button and select your  
preferred MP3 player, then click OK.  
3 About button  
Clicking on this button will display the  
version of VX200 Manager and its  
copyright information.  
14 ENGLISH  
 
4 List of File Type box  
The default file type argument *.mp3 can  
be used to display the MP3 files in the  
current folder.  
12 Initialize, Download, and  
Upload buttons (Flash Memory)  
Initialize button  
Select the file type argument *.wav to  
display WAV files.  
Selectthefiletypeargument*.*todisplay  
all types of files.  
This will initialize the Flash Memory in the  
player. All files stored in Flash Memory  
will be erased. You may need to initialize  
Flash Memory when for some reason the  
player is not being recognized by the  
VX200 Manager software.  
5–9 Cut, Copy, Paste, Delete, and  
Rename buttons  
Send to VX200 (Download) button  
These buttons work the same as those of  
Microsoft Windows Explorer. You can  
cut, copy, paste, delete, rename or move  
the files you select in the display list box  
(localdisplaylistbox)ofthePC.However,  
folders will not be moved or copied.  
TocopyMP3filesanddatafilesfromyour  
PC to the player, drag and drop or use the  
Send to VX200 (Download) button  
.
Using the mouse, just select the files you  
wish to download to the player. Then,  
drag and drop them into the display list  
box of Flash Memory.  
If you wish to copy some files to a folder,  
select the files and drag and drop them  
while holding the Ctrl key pressed.  
Note  
VX200 Manager will not allow you to  
download the MP3 files more than 3  
times.  
10 New Folder button  
A new folder under the selected folder in  
the local display list box will be created.  
The file name of xxx.mp3will be  
changed  
to  
xxx.mpm”  
after  
downloading.  
11 Update button on the local  
display list box  
If the information in the local display list  
box has been changed, click the Update  
button to refresh the local display list box.  
You can download the MP3 files only  
from the hard disc drive of your PC. For  
example, theMP3filesintheCD-Rdrive  
cannot be downloaded with the VX200  
Manager.  
You cannot download any files during  
playback of voice recording.  
In this case, stop playback or voice  
recording and click the Update button  
(section 15 ) to download the files.  
Send to PC (Upload) button  
You can also copy data files and PCM  
(voice recording) files from the player to  
the selected folder on your PC. If you use  
the Send to PC (Upload) button  
to  
copy them onto your PC, you must select  
one folder as a destination. The MP3 files  
storedintheplayercannotbecopiedonto  
your PC.  
ENGLISH 15  
 
Note  
14 Delete button  
VX200 Manager will not allow you to  
upload MP3 files from the player to your  
PCbecauseofcopyrightconsiderations.  
Only data files and voice files can be  
uploaded to your PC.  
A selected file in either Flash Memory or  
SmartMedia-IDwillbehighlightedinblue.  
Just click on the Delete button to remove  
a file highlighted in blue.  
If the player is turned off during a copy  
process on purpose or because of  
insufficientbatterypower,thetransferred  
datamightbecorrupted.Youmightneed  
to initialize the player.  
You cannot upload any files during  
playback of voice recording.  
In this case, stop playback or voice  
recording and click the Update button  
(section 15 ) to upload the files.  
15 Update button (Flash Memory)  
If the information in the display list box  
has been changed, click on the Update  
buttontorefreshtheFlashmemorydisplay  
list box.  
Note  
You cannot download or upload any files  
during playback of voice recording.  
In this case, stop playback or voice  
recording and click this Update button  
to download or upload the files.  
Caution  
Before you copy a data file or an PCM file  
onto your PC, be sure to rename the file.  
If a file with the same filename already  
existswhenyoucopythefiles,theprevious  
copied file will be erased automatically  
and the file will be replaced with a new  
one.  
16 SmartMedia-ID format button  
If you use the SmartMedia-ID formatted  
by VX200 Manager with a digital camera  
orotherplayers,clickthisbuttontoformat.  
17 Local Display list box  
13 Initialize , Download  
and Upload buttons  
(SmartMedia-ID)  
These buttons operate as described in  
section 12.  
If you insert a new SmartMedia-ID, you  
must initialize the SmartMedia-ID by  
clicking on the Initialize button.  
,
Thislistboxshowsthefilesstoredonyour  
PC, such as the MP3 files and data files  
that you want to copy to the player. The  
defaultfiletypeargument*.mp3willdisplay  
only MP3 files in the current folder. You  
may also select the file type argument *.*  
to display all files or specify a type of file  
to be displayed.  
You may also select *.wav to display the  
voice files you recorded. Even if you see  
the standard wave format files, however,  
you can play back only the voice file  
recorded with the MM-VX200 player.  
Note  
VX200 Manager will not allow you to  
download the MP3 files more than 3  
times.  
You cannot copy any MP3 files from the  
player to your PC.  
The file name of xxx.mp3will be  
changed  
to  
xxx.mpm”  
after  
downloading.  
The MP3 files in the SmartMedia-ID  
cannot be played back with other player  
due to SmartMedia-ID.  
16 ENGLISH  
 
To select multiple files  
MP3 file info  
While holding the Ctrl key on the  
keyboard pressed, click on the desired  
files. If you click on a highlighted file, the  
file will be unselected.  
If you click on a file while holding the  
Shift key pressed, the files between the  
first click and the release of the mouse  
button will be highlighted.  
Youcanmodifyfiledescriptions(ID3tags)  
for any MP3 files selected in the local  
display list box. ID3 tag information can  
be changed by selecting the MP3 Info  
from the menu. Clicking on the Modify  
buttonwillreplacetheID3taginformation  
of the selected MP3 file with the ID3 tag  
information you have input.  
The total size of the selected files in the  
local display list box will be displayed  
below the list box.  
ClickingontheRemovebuttonwillremove  
the ID3 tag information from the selected  
MP3 file.  
Click on the Modify button to update the  
ID3taginformationaftermakingachange.  
Otherwise, the information does not  
change even if you have input new data.  
18 Flash Memory Display list box  
TheupperrightlistboxofVX200Manager  
is the Flash Memory display list box.  
All files in Flash Memory (built-in memory  
of the player) will be displayed in this list  
box.  
Thesizesoftotalandavailablememoryin  
theplayeraredisplayedinkilobytesbelow  
the list box.  
Note  
The filename displayed on the display of  
the player will be the Title, Artist name  
andAlbumtitleiftheyarecontainedinthe  
ID3 tag of the MP3 file. If the ID3 tag does  
not contain the Title, Artist name and  
Album title, only the MP3 filename,  
excluding the MP3 extension, will be  
displayed on the display.  
ENGLISH 17  
 
1 PLAYER OVERVIEW . . . . . . . . . 18  
2 DISPLAY OVERVIEW. . . . . . . . . 20  
3 PLAYER OPERATION . . . . . . . . 21  
Chapter 4  
PLAYER OPERATION  
This chapter provides an overview of the  
display and operation of the player.  
PLAYER OVERVIEW  
1
Main unit  
1MP3 button  
Press to enter MP3 mode, in which you  
can play MP3 files.  
Press repeatedly to display the MP3  
song information such as MPEG Type,  
Sampling Rate and Bit Rate.  
2\ jack  
Connect the supplied remote control.  
3Display window  
5s POWER OFF button  
Press to stop playback or recording.  
Keep pressed for 1 second to turn off  
the power.  
6r button  
Press to go back to the beginning of  
the current track or previous track.  
Keep pressed during playback to  
search for a desired point.  
7A-B button  
Press to repeat a certain portion of the  
current track.  
8USB port connector  
Connect the Series B connector of the  
supplied USB cable to connect the  
player to your PC.  
4HOLD switch  
Release before use to activate the  
buttons. When not in use, set it to the  
HOLD position to prevent unintentional  
operation.  
18 ENGLISH  
 
9VOLUME button  
%t button  
Press to adjust the volume. The volume  
level ranges from 0 to 20.  
0VOICE button  
Press to enter Voice mode, in which  
you can create and play voice files.  
Press again to display the sampling  
frequency of the voice file for 3  
seconds.  
Press to skip to the beginning of the  
next or succeeding track.  
Keep pressed during playback to  
search for a desired point.  
^PLAY MODE button  
Press repeatedly to select the playback  
mode.  
&DTP button  
Press repeatedly to select the preset  
!ERASE button  
Press to erase the current MP3 or  
equalizer.  
voice file.  
*REC/STOP button  
@Built-in microphone  
Records your voice messages.  
#DC 3 V jack  
Connect the AC adaptor Aiwa AC-D302  
(not supplied).  
$e POWER ON button  
Keep pressed for 1 second to turn on  
the power.  
Press to start recording using the built-  
in microphone in Voice mode.  
Press again to stop recording.  
You cannot start recording while any  
MP3 or voice file is being played.  
(Battery compartment  
Insert an LR6 (size AA) alkaline  
battery.  
)SmartMedia-ID slot  
Insert your SmartMedia-ID (16MB,  
32MB, or 64MB) into this slot.  
Press to start playback of an MP3 or  
voice file.  
Press during playback to pause, and  
press again to resume.  
Remote control  
1VOL control  
2Headphone jack  
3e button  
4s POWER OFF button  
5HOLD switch  
6DTP button  
7t button  
8r button  
ENGLISH 19  
 
DISPLAY OVERVIEW  
2
Display window  
12 3 4 5 6 7  
@
! 0 9 8  
1Battery Indicator  
This displays the remaining battery  
power.  
2HOLD Icon  
This indicates that the HOLD switch is  
set to the HOLD position.  
3Playback mode Icon  
This indicates the selected playback  
mode.  
7Elapsed playback/recording time  
This indicates the elapsed time in  
minutes and seconds separated by a  
colon of the track currently being  
played or recorded.  
8Remaining recording time  
This appears during voice recording.  
9Total number of tracks  
This indicates the total number of MP3  
files or voice files.  
(No Icon) Normal  
Repeat  
Repeat All  
Random  
Random Repeat All  
0Current track number  
This indicates the file number of the  
current MP3 or voice file.  
!Title  
The MP3 title or voice file name is  
displayed during playback or voice  
files. A voice filename will look like  
PAGE xx; where xx is a file number  
from 0 to 99. If an MP3 file contains the  
Title, Artist name and Album title in its  
ID3 tag, the Title, Artist name and  
Album title will be displayed. If the MP3  
file does not contain the Title, Artist  
name and Album title, only the MP3  
filename excluding the extension  
(.MP3) will be displayed.  
4Segment Repeat (A-B)  
This indicates the specified location (a  
portion being repeated) of the currently  
playing file.  
5Volume Icon  
This indicates the volume level on a  
scale of 0 to 20.  
@Status  
6Memory Icon  
This box shows information on the  
current status of play, pause and  
record.  
This indicates the remaining available  
memory in megabytes.  
20 ENGLISH  
 
MP3 playback  
PLAYER OPERATION  
3
Turning the power on and off  
2
3
\
1
DTP  
POWER  
OFF  
HOLD  
POWER  
ON  
POWER  
OFF  
PLAY  
MODE  
A-B  
4
POWER OFF  
DTP  
HOLD  
POWER OFF  
1 Connect the supplied remote  
control to the \ jack of the player  
and connect the supplied  
headphones to the remote  
control.  
First, releasetheHOLDswitchtoactivate  
the buttons of the player.  
Press the e POWER ON button to  
turn on the player.  
The power will turned off automatically  
after about 3 minutes from the last  
operation (Auto Power Off function). To  
turn off the power before the Auto Power  
Off function turns off the power, keep the  
sPOWER OFF button pressed for 1  
second.  
2 Press the MP3 button to select  
MP3 playback mode.  
3 Press the e button to start  
playback.  
Playback starts from the MP3 file that  
you played last time.  
4 Adjust the volume.  
When operating with the remote control  
Press the e button.  
The power is turned on, and playback of  
MP3 files starts automatically.  
After use, press the s POWER OFF  
button to stop playback. The power is  
turned off automatically.  
Press the r or t button to change  
the track number.  
To stop playback, press the s POWER  
OFF button.  
ENGLISH 21  
 
To select a preset equalizer  
PresstheDTPbuttonrepeatedlytoselect  
a desired equalizer mode.  
Classic Normal sound setting  
Rock Optimized sound setting for  
Rock music  
Note  
You can specify a location to be repeated  
only in one MP3 file at a time. If the end of  
the current track is reached before you  
press the A-B button again, repeat  
playback is canceled automatically.  
Pop  
Optimized sound setting for  
Pop music  
Voice recording  
Jazz  
Optimized sound setting for  
Jazz music  
1
2
To select other playback modes  
PressthePLAYMODEbuttonrepeatedly  
toselectaplaybackmodeofthefollowings.  
Each time the button is pressed, the  
playback mode changes in the following  
order.  
POWER  
OFF  
Normal  
Plays all stored MP3 songs  
in order, then stops after  
the last song.  
3
Repeat  
Plays the current song  
repeatedly.  
Youcanrecordyourvoicemessageinthe  
built-in Flash Memory of the player.  
Repeat All Plays all stored MP3 songs  
repeatedly.  
Random Plays all stored MP3 songs  
in random order.  
1 Press the VOICE button to select  
voice mode.  
2 Orient the built-in microphone to  
the sound source.  
Random Repeat All  
Plays all stored MP3 songs  
inrandomorderrepeatedly.  
3 Press the REC/STOP button to  
start recording.  
To repeat a certain area  
Procedure during MP3 playback  
To stop recording, press the REC/  
STOP button or the s POWER OFF  
button.  
Eachtimerecordingstopsbypressing  
the REC/STOP button or the s  
POWER OFF button, the recording  
track number increases.  
1 Press the A-B button at the  
beginning of the phrase to be  
repeated.  
2 Press the A-B button again at the  
end of the phrase to be repeated.  
Playback starts between the marked  
locations repeatedly. When the end of  
thelocationisreached,playbackstarts  
againfromthebeginningofthemarked  
location automatically.  
Note  
You cannot record voice messages  
directly into the SmartMedia-ID in the  
player.  
To cancel repeat playback of the  
location, press the A-B button during  
repeat playback.  
22 ENGLISH  
 
To playback a recorded voice  
message  
Erasing Files  
2,3  
1
2
3
\
1
POWER  
OFF  
MP3 or voice files can be erased without  
using VX200 Manager.  
1 Connect the supplied remote  
control to the \ jack of the player  
and connect the supplied  
headphones to the remote  
control.  
1 During stop mode, press the r  
or t button to select a track to  
be erased from an MP3 file or  
voice file.  
2 Press the ERASE button.  
2 Press the VOICE button to select  
voice file playback mode.  
3 Press the ERASE button again to  
erase the current track.  
To cancel erasing, press a button other  
3 Press the e button to start  
playback.  
than the ERASE button.  
Press the e button to pause, and  
press it again to resume playback.  
Presstherortbuttontochange  
the track number.  
To stop playback, press the s POWER  
OFF button.  
ENGLISH 23  
 
NOTE  
FOR USE IN THE U.S.A.  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference in a residential installation.  
Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledand  
usedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.  
However, there is no guarantee that interference will not occur in a particular installation. If this  
equipment does cause harmful interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and receiver.  
– Connect the equipment into an outlet on circuit different from that to which the receiver is  
connected.  
– Consult the dealer or an experienced radio/TV technician for help.  
CAUTION  
Modifications or adjustments to this product, which are not expressly approved by the  
manufacturer, may void the user’s right or authority to operate this product.  
DECLARATION OF CONFORMITY  
AIWA AMERICA INC. declares, in sole responsibility, that the following product referred to  
in the declaration conforms to the following standard, tested on the basis of FCC standard  
with the Class B device.  
Type of product : Portable MP3 Player  
Brand Name  
Model Name  
: AIWA  
: MM-VX200  
ANSI C63.4 1992  
FCC PART 15 SUBPART B  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference; and (2) this device must accept  
any interference received, including interference that may cause undesired operation.  
AIWA AMERICA INC.  
800 Corporate Drive, Mahwah NJ 07430-2048 U.S.A.  
Tel: 201-512-3600  
Fax: 201-512-3710  
For assistance and information,  
call toll free 1-800-BUY-AIWA. (United States and Puerto Rico)  
8A-HZ1-911-01  
000721AYO-O-K  
Printed in Korea  
 

Abocom Network Router WR104 User Manual
Adaptec Network Card PC 104 User Manual
Agilent Technologies Portable Generator 08111 90002 User Manual
Air King Fan 3C614D User Manual
Allied Telesis Switch AT GS950 48PS User Manual
American DJ DJ Equipment 700TM User Manual
Bacharach Carbon Monoxide Alarm 24 9351 User Manual
Bakers Pride Oven Oven VH 1828G 1 User Manual
Beko Refrigerator CFD640B User Manual
Beko Refrigerator CN232121 User Manual