Coleman Tent 2000001598 User Manual

®
WEATHERMASTER 10 TENT  
MODEL 2000001598  
6. Rotate all six Leg Poles upright and insert  
Before you begin  
pin on each web loop at the side locations  
as shown. (Fig. 7 & 7A)  
Read all instructions before set up.  
7A  
Pin  
• Select a level site clear of rocks, branches, and other hard or sharp  
objects, to install your tent.  
WARNING: Keep clear of overhead power lines.  
• Do not set up your tent under trees because of potential lightning strikes  
or falling tree limbs in inclement weather.  
• Secure with all stakes and guylines provided to prevent property damage  
or personal injury.  
• For best results in windy conditions, position narrow end of tent into  
the wind.  
• Enlist the help of at least one other person to assist you when it is time  
to assemble the tent.  
Pole Descriptions  
Pole  
Pole  
Pole  
Description  
Qty. Dia.  
Repair Kit Replacement Kit  
Long Leg Pole, steel  
(w/ red marking)  
Short Leg Pole, steel  
7B  
2
4
19mm  
19mm  
N/A  
N/A  
5010000614  
5010000623  
Fig. 7  
Metal Tip  
Hole in  
Curved Ridge Pole, steel  
(w/ red marking)  
1
2
19mm  
19mm  
N/A  
N/A  
5010000613  
5010000615  
Sleeve  
Leg Pole  
Curved Ridge Pole, steel  
Side Window Pole, black,  
fiberglass, metal tips  
Door Pole, long, thin ,black,  
fiberglass, rubber tips  
Vert. Door Pole, short, black,  
fiberglass, rubber tips  
Window Pole  
7C  
2
1
1
8.5mm 5010000541 5010000547  
6.3mm 5010000543 5010000545  
6.3mm 5010000543 5010000545  
6. Assemble the two, shock-corded, black Window Poles, then  
insert one into sleeve located at each end of tent. (Fig. 7 & 7B)  
7. Insert tapered metal tip on Window Pole into Leg Pole.  
NOTE: It may be necessary to gently rotate Leg Pole so the  
hole will line up with the Window Pole.  
8. Go to opposite end of each window pole and gradually apply  
pressure to the pole forming an arch. Insert the pin into the  
leg pole end at the corners of tent. (Fig. 7 & 7C)  
9. Locate the plastic hooks at sides and corners of tent, then  
snap onto Leg Poles to attach. (Fig. 8)  
To Set Up Tent  
1. Unfold tent and spread out on a clean, level surface with the  
door facing the desired direction. Unzip doors. (Fig. 1)  
Fig. 1  
10. Locate web strap  
Door  
Fig. 8  
Fig. 9  
Corner  
Leg  
Pole  
with plastic hook on  
the sides of each  
end panel Window  
Vent, then snap onto  
the corner Leg Pole.  
(Fig. 9)  
2. Pull four corners of tent taut, then secure by  
driving stakes through web loops at an angle  
for better anchoring. (Fig. 2)  
Window Vent  
Web Tent Strap  
Fig. 2  
11. To stretch tent to finished size:  
Fig. 10  
3. Assemble three, steel, shock-corded,  
curved Ridge Poles. Insert Ridge Pole  
(with red marking) into center sleeve  
on top of tent with the red trim (Fig. 3).  
Insert the remaining curved Ridge Poles  
into the other two sleeves on top of tent.  
Fig. 3  
• Push in button on Leg Pole while  
twisting lower Leg Pole section  
counterclockwise (Fig.10);  
• Pull up on top Leg Pole section until  
tent is taut;  
• Twist the lower Leg Pole clockwise  
until the button locks into the center  
or lowest hole;  
Ridge Pole  
with Red  
Marking  
Upper  
Leg Pole  
Section  
Sleeve  
with Red  
Trim  
Button  
Center Hole  
Lower Hole  
4. Assemble six, steel, shock-corded, Leg Poles. Push down  
on steel button on tapered end and insert into end with  
four holes.  
NOTE: Make sure steel button locks  
into third hole on pole as shown. (Fig.4)  
5. Insert curved end of Leg Poles  
Lower  
Leg Pole  
Section  
• Repeat on remaining Leg Poles.  
12. Insert plastic stakes through web straps  
located on both sides of tent, then drive  
in to secure. (Fig. 11)  
Button in third hole  
Fig. 4  
(with red marking) into  
the ends of the Ridge  
Pole (with red marking).  
Ridge Pole with  
Red Marking  
Fig. 11  
Insert curved end of  
remaining short Leg  
Poles into the ends of  
the remaining Ridge  
Poles. (Fig. 5 & 6)  
Hinged, Rigid Door  
Fig. 12  
Sleeve  
Sleeve  
with Red  
Trim  
Curved End of  
Long Leg Pole  
1. Assemble Vertical Door Pole (shorter  
black pole with plastic cap tips); then  
insert through zippered sleeve on side  
of door and into hinge. (Fig. 12)  
Fig. 5  
Fig. 6  
Ridge Pole with  
Red Marking in  
center sleeve  
Hinge  
(continued on other side)  
 

Cooper Lighting Indoor Furnishings CMOB User Manual
Craftsman Spreader 486243222 User Manual
Digicom Network Router ADSL2+ Router User Manual
Dixon Lawn Mower 16134 0803 User Manual
Dodge Automobile 2004 Freightliner User Manual
Edimax Technology Network Router Wireless VPN Broadband Router User Manual
Edimax Technology Switch ES 5240G+ User Manual
Fundex Games Games 0728 User Manual
GE Air Conditioner AEQ24DK User Manual
GE Washer Dryer WSM2700H User Manual