Cornelius Ice Maker P N 630000408 User Manual

IMI CORNELIUS INC g One Cornelius Place g Anoka, MN 55303-6234  
Telephone (800) 238-3600 Facsimile (800) 535-4321  
INSTALLATION INSTRUCTIONS, BIN STAT KIT, P/N 630000408  
These Bin Stat kits apply to all “I” Series Ice makers  
Table 1. Loose–Shipped Parts  
Item No.  
Part No.  
630900413  
70894  
Name  
Qty.  
1
1
1
1
1
1
1
1
2
3
4
5
6
7
Spacer, Hex 5/8” Long x 8–32 SS  
Screw MA 08–32 TRPH 24 SS  
Spacer  
Thermostat Asy  
Bin Stat Support  
51348  
630000413  
620037008  
630460064INS  
168833002  
Installation Instruction, Thermostat  
Washer SR 4W SS E#8  
1. Disconnect power.  
2. Remove front cover of the unit and the electrical box cover plate.  
3. Carefully insert the coiled capillary tube through the bottom hole in the electrical box where the elec-  
trical wires are coming through (see Figure 4).  
4. If there is not a hole already in the chassis base, drill a ½” hole in the chassis base as indicated in  
Figure 3.  
5. Straighten approximately 12” of cap tube to go through hole. Re–coil the remainder. Do not disturb  
coiled end.  
6. Insert the “1/4” diameter wire form support into the coiled end of capillary tube and insert the assem-  
bly through the hole in the chassis base. Route capillary tube to follow support as closely as pos-  
sible.  
7. Remove the 8–32 nut (closest to the ½” DIA hole) that holds the compartment wall to the base. The  
adapter kits that have a single level, adapter kits P/N’s 02390, 630200153, 08006, 02388, 08004,  
630000191 and 08010) require a 7/8” high spacer be used to mount the binstat support. Thread the  
8–32 x 5/8” hex spacer on to the compartment stud. Then fasten the thermostat support to the hex  
spacer using the ¼” high plastic spacer, #8 flat washer and 8–32 x ¾” long phil. head screw. The  
spacers are not to be used on the elevated adapter kits. Refer to Figure 2.  
8. Any excess capillary tubing must be pulled back into the compressor compartment to prevent ice  
from damaging it during dispenser operation.  
9. Seal ½” diameter hole with sealant (RTV).  
March 2, 2004  
IMI CORNELIUS INC. 2004  
1
Rev A  
630460064INS  
 
March 2, 2004  
Rev A  
630460064INS  
IMI CORNELIUS INC. 2004  
3
 
BIN STAT SUPT ASY FOR  
SINGLE LEVEL ADAPTOR KIT NO:  
02388, 08004,630000191, 02390,  
630200153, 08006, & 08010  
WASHER  
ICEMAKER E-BOX  
832 X 3/4 PHMS  
620037008, BIN STAT SUPT  
CAPILLARY TUBE  
COIL CAPILLARY TUBE  
AROUND BIN STAT SUPT  
1/4 SPACER  
5/8 SPACER  
ELEVATED  
ADAPTOR KIT  
CAPILLARY ASY  
832 NUT (PART OF ICEMAKER)  
WASHER  
620037008, BIN STAT SUPT.  
832 STUD (PART OF ICEMAKER)  
SINGLE LEVEL  
ADAPTOR KIT  
BIN STAT SUPT ASY FOR ALL  
ELEVATED ADAPTOR LID KITS  
FIGURE 2  
 
TOP VIEW OF 1230 CHASSIS PLATE  
ICE  
DROP  
ZONE  
ICE  
DROP  
ZONE  
ICE  
DROP  
ZONE  
1/2DRILL  
ICE  
DROP  
ZONE  
4.25*  
1.50  
* DIMENSION IS FROM FRONT  
OF UNIT WITHOUT COVER.  
15.41  
Figure 3  
CLEAN MOUNTING AREA WITH  
SCOTCH BRITE PAD,  
ELECTRICAL BOX ASY  
THEN WIPE AREA DOWN WITH  
RUBBING ALCOHOL AND LET DRY  
THERMOSTAT KIT ASY  
630000408  
COIL  
TO CHASSIS  
PLATE  
Figure 4  
March 2, 2004  
Rev A  
630460064INS  
IMI CORNELIUS INC. 2004  
5
 

Craftsman Tiller 917292394 User Manual
Cuisinart Coffeemaker DCC 1100BK User Manual
Danby Refrigerator DCRM71BLDB User Manual
Delta Electronics Power Supply Series DNT12 User Manual
Delta Electronics Power Supply SIT612 User Manual
Delta Electronics Power Supply THAR0806 User Manual
Dynex TV Mount DX TVMLPTB03 User Manual
Estate Refrigerator W10316633A User Manual
Garmin Chainsaw 353 User Manual
GE Trash Compactor GCG1500LBB User Manual