Delta Electronics Network Card TAP CN01 02 03 User Manual

1
2
3
4
5
6
7
8
DeviceNet/CANopen main cable connector  
DeviceNet/CANopen main cable connector  
DeviceNet/CANopen sub cable connector  
DeviceNet/CANopen sub cable connector  
DeviceNet/CANopen sub cable connector  
Termination resistance setup switch  
121termination resistance  
96.50[3.80]  
Electrical Circuit  
TAP-CN01  
2
6
1
TAP-CN02  
7
8
Thick Cable  
TB1  
Thick Cable  
(OPEN TYPE)  
/
TB2  
S
V+  
H
V+  
H
(
)
3
4
5
DIN rail  
Unit: mm  
V-  
L
S
H
V+  
V-  
L
H
V+  
S
S
L
L
1
2
3
4
5
6
7
8
DeviceNet/CANopen main cable connector  
DeviceNet/CANopen main cable connector  
DeviceNet/CANopen sub cable connector  
DeviceNet/CANopen sub cable connector  
DeviceNet/CANopen sub cable connector  
Termination resistance setup switch  
121termination resistance  
66.50[2.62]  
V-  
V-  
/
V+  
H
V+  
H
V+  
1
7
2
6
H
S
L
8
S
S
L
L
TAP-CN01/CN02/CN03  
CANopen  
TAP-CN01/CN02/CN03  
TB1 TB2  
SW  
DeviceNet  
CANopen  
V-  
V-  
V-  
V-  
L
S
H
V+  
DeviceNet  
TB3 ~ TB5  
3
4
5
TB3  
TAP-CN01/CN02/CN03  
121  
TB3  
TB4  
TB5  
Unit: mm  
DIN rail  
Thin Cable  
Thin Cable  
Thin Cable  
Specifications  
TAP-CN03  
Electrical Specifications  
CN010000W7250001  
V+  
H
V+  
DeviceNet  
Voltage: 11 ~ 25V DC (supplied by the power cable in the network)  
MADE IN XXXXXX  
H
S
Environment  
S
Operation: 0ºC ~ 55ºC (temperature), 50 ~ 95% (humidity), pollution degree 2  
L
L
Operation/Storage  
CN0X000  
0
W
7 25 0001  
Storage: -25ºC ~ 70ºC (temperature), 5 ~ 95% (humidity)  
V-  
V-  
How to Install  
Approx. 30mm  
8
765 43  
2
1
8
76  
5
43  
2
1
8
76  
5
4
3
2
1
Use efficient tool to peel the communication cable  
for approx. 30mm. DO NOT damage the shielded  
cable while peeling.  
Shielded cable  
TB3  
TB4  
TB5  
66.50[2.62]  
DeviceNet/CANopen  
DeviceNet/CANopen  
DeviceNet/CANopen  
1
2
3
4
5
6
Peel off the metallic shielded net and foil and you  
will see 2 power cables (in red and black), 2 signal  
cables (in blue and white) and 1 shielded cable.  
Thin Cable  
Thin Cable  
Thin Cable  
1
3
2
6
Components  
DeviceNet/CANopen Connector  
5
4
Peel off the exterior metallic shielded net, foil and  
the plastic cover of the power cable and signal cable  
in proper length.  
121  
To connect with the DeviceNet/CANopen network, use the connector enclosed with TAP-CN01/02/03 or any  
connectors you can buy in the store for wiring.  
DIN  
mm  
Black (V-)  
Blue (CAN_L)  
96.50[3.80]  
PIN  
V-  
L
Signal  
V-  
Description  
0V DC  
1
2
3
4
5
6
7
8
DeviceNet/CANopen  
DeviceNet/CANopen  
DeviceNet/CANopen  
DeviceNet/CANopen  
DeviceNet/CANopen  
ENGLISH  
Warning  
Shielded cable (CAN_SHLD)  
V+  
H
2
6
1
Insert the peeled communication cables into the  
holes in the connector in correct order.  
Please read this instruction sheet carefully before use and follow the sheet to operate TAP-CN01//02/03 in order to  
prevent damages on the device or injuries to staff.  
CAN_L  
SHIELD  
CAN_H  
V+  
Signal-  
S
L
7
8
S
Shielded cable  
Signal+  
Switch off the power before wiring.  
V-  
Red (V+)  
White (CAN_H)  
H
This instruction only provides introductory information on electrical specifications, functions, wiring,  
trouble-shooting and peripherals for TAP-CN01/02/03.  
V+  
24V DC  
TAP-CN01/02/03 is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust,  
humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the  
device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device may  
occur.  
4
121  
3
5
mm  
PIN  
1
Signal  
CAN_H  
Description  
Signal+  
DIN  
Tighten the screws on the connector by a slotted  
screwdriver, and fix the communication cables in  
the holes in the connector.  
1
2
3
4
5
6
7
8
DeviceNet/CANopen  
DeviceNet/CANopen  
DeviceNet/CANopen  
DeviceNet/CANopen  
DeviceNet/CANopen  
In order not to damage it, only qualified professional staff familiar with the structure and operation of  
TAP-CN01/02/03 can install, operate, wire and repair it.  
2
CAN_L  
Signal-  
66.50[2.62]  
3
CAN_GND  
RESE_1  
RESE_2  
CAN_SHLD  
CAN_GND  
CAN_V+  
0V DC  
Screw by  
a
slotted screwdriver.  
DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check all  
the wiring again before switching on the power and DO NOT touch any terminal when the power is switched on.  
1
7
2
4
Reserved  
Reserved  
Shielded cable  
0V DC  
Use standard 35mm DIN rail.  
8
7 6 5 4 3 2 1  
8
6
5
Mount TAP-CN01/CN02/CN03 onto the DIN rail.  
6
Introduction  
7
Thank you very much for choosing Delta TAP-CN01/02/03 distribution box. TAP-CN01/02/03 is the distribution  
box for the connection of main cable and sub cable in DeviceNet or CANopen. TB1 and TB2 are for connecting  
3
4
5
121  
TAP-CN02  
TAP-CN03  
TAP-CN01  
8
24V DC  
main cables, and TB3 ~ TB5 are for connecting sub cables. TAP-CN01/02/03 formulates  
resistance, which is switched by the setup switch.  
a
termination  
mm  
DIN  
O
F
F
Termination Resistance Setup Switch  
Nameplate Explanation  
O
F
F
The termination resistance switch is used for determining whether the resistance is valid.  
ON = valid; OFF = invalid.  
ON  
O
F
F
OFF  
Model name  
Version  
DeviceNet  
11 ~ 25V DC  
Barcode, Serial No.  
Termination Resistance  
CN010000W7250001  
Insert the connectors into TAP-CN01/CN02/CN03.  
MADEIN XXXXXX  
TAP-CN01/CN02/CN03 formulates a 121termination resistance.  
0ºC ~ 55ºC  
-25ºC ~ 70ºC  
50 ~ 95%  
5 ~ 95%  
2
/
Serial No. Explanation  
CN0X000  
0
W
7
25 0001  
Connection Example  
Production No.  
Production week  
Establishing  
a
network through TAP-CN01/CN02/CN03:  
Production year (2007)  
Insert the connector into  
TAP-CN02 terminal.  
Insert the connector into  
TAP-CN01 terminal.  
Production plant (W: Wujiang T: Taoyuan)  
Version No.  
30mm  
Model name  
TAP-CN01  
TAP-CN02  
TAP-CN03  
Main cable  
Main cable  
Main cable  
Sub cable  
Product Profile & Outline  
66.50[2.62]  
Sub cable  
Sub cable  
1
2
3
4
5
6
DeviceNet/CANopen main cable connector  
DeviceNet/CANopen main cable connector  
DeviceNet/CANopen sub cable connector  
Termination resistance setup switch  
121termination resistance  
2
2
1
Insert the connector into  
TAP-CN03 terminal.  
1
3
2
6
Notes:  
5
4
To install TAP-CN01/CN02/CN03 in the starting point or end of the network, you have to switch ON the  
termination resistance. To install TAP-CN01/CN02/CN03 in the middle of the network, you have to switch  
OFF the termination resistance.  
1. Use only wires specifically designed for DeviceNet/CANopen for wiring.  
2. The terminal screws shall be tightened to 5.18 kg-cm (4.5 in-lbs).  
3. DO NOT place the signal cable and power cable in the same wiring circuit.  
DIN rail  
When using TAP-CN01/CN02/CN03 to establish a DeviceNet/CANopen network, the sub cable cannot be  
longer than 6m.  
Unit: mm  
 

Clarion CD Player DXZ466MP User Manual
Coleman Burner 5428A Series User Manual
Delta Electronics Power Supply SI54 User Manual
Delta Electronics Power Supply SIQ125R User Manual
Dynex Computer Drive DX HDEN20 User Manual
Edimax Technology Security Camera IR 112E User Manual
Fisher Price Video Games T3902 User Manual
GCC Printers Printer ELITE 12 User Manual
Gitzo Camcorder Accessories GT2942 User Manual
Glen Dimplex Home Appliances Ltd Gas Grill BI 70 G User Manual