Extron electronic Stereo Amplifier DVI DL 201 RX User Manual

Setup Guide — DVI DL 201 Tx/Rx  
The Extron® DVI DL 201 Tx and DVI DL 201 Rx are dual  
link DVI transmitter (Tx) or receiver (Rx) units. Using  
three CAT 5/5e/6/7 twisted pair cables, DVI-D signals  
can be extended up to 100 feet (30 m) at resolutions up to  
2560x1600 @ 60 Hz. They can be purchased as a pair or as  
individual units.  
These instructions provide a quick setup guide for experienced installers. Installation  
and service must be performed by authorized personnel only.  
W
The DVI DL 201 Tx/Rx works with unshielded twisted pair (UTP) cable or shielded twisted  
pair (STP) cable. STP cables are required to ensure FCC Class A and CE compliance.  
N
Always use a power  
supply specified by  
Extron for this unit.  
Use of an unauthorized  
power supply voids all  
regulatory compliance  
certification and  
C
Extron  
DVI DL 201 Tx  
Dual Link DVI  
Transmitter  
CAT 5/5e/6/7 Cables  
up to 200 feet  
3
2
1
T
D
O
N
O
CONNECT  
OUTPUTS  
O
LAN  
T
LOCAL O
T
VI-D INPU  
D
2
3
-2  
U
S
R
OUTE  
TE  
REMO  
ASS-THR  
P
DDC  
R
WER  
PO  
X
12V  
0.4A MA  
LOCAL  
may cause damage  
ARE  
SP  
to the supply and the  
transmitter or receiver.  
RS-232  
Local  
One power supply is provided  
when the transmitter and  
receiver are purchased  
N
Monitor  
Control  
System  
PC w/ Dual Link DVI  
Output  
L
R
O
H
R
T
x
T
S
R
U
N
S
O
C
P
A
x
T
RS-232  
DVI DL 201 Rx  
together. A power supply is  
not provided when either unit  
is purchased separately.  
DVI-D O
Extron  
DVI DL 201 Rx  
Dual Link  
DVI Cable  
Dual Link DVI  
Receiver  
Step 1  
Turn off all equipment or disconnect  
it from power sources. Mount the  
transmitter and receiver as desired.  
Follow the instructions included with the  
appropriate mounting kit.  
2560 x 1600 Flat Panel  
Display with Dual-Link  
DVI Input  
CONTROL  
PASS THRU  
Tx Rx  
CONTROL  
PASS THRU  
Tx Rx  
B.  
A.  
Step 2  
Use the three port captive screw  
DVI DL 201  
Transmitter  
or Receiver  
DVI DL 201  
Transmitter  
or Receiver  
connections to transmit pass-through  
RS-232 and IR signals from a control  
device to a remote device. RS-232 signals  
are bidirectional and use three wires  
(see diagram A. at right). IR signals are  
unidirectional and use two wires (see  
diagram B. at right). In each case the  
control device is wired to the transmitter in  
exactly the same way as the remote device  
is wired to the the receiver.  
RS-232 Control  
or Display Device  
IR Control  
or IR emitter  
Tx Rx  
S
G
Step 3  
Determine how the source device will obtain the EDID information and perform  
one of the following procedures:  
Option 1 — To capture the EDID of a desired display and store it in the EDID  
Minder for future use:  
ON  
a. Connect the display to the local monitor output of the transmitter.  
b. Power on the transmitter and the local monitor.  
ON  
1
2
3
c. Configure the DDC switches as shown in the figure at right.  
OFF  
 

Coleman Stove 5466 User Manual
Continental Iron CM43095 User Manual
Cooper Lighting Indoor Furnishings CPP CPS User Manual
Cornelius Beverage Dispenser 326142000 User Manual
Craftsman Snow Blower 53688123 User Manual
Creative Network Router PCMCIA DI5611 User Manual
Earlex Heat Gun HG 1600K User Manual
Gefen Network Router DVI 1600HD User Manual
Glem GasEmilia Dishwasher DW410 User Manual
Global Machinery Company Cordless Drill DP250LS User Manual