GE Telephone EX29268 User Manual

TEMPORARY TONE FEATURE  
BEFORE YOU BEGIN  
29268  
Telephone  
User’s Guide  
If you have Pulse ( rotary ) service and want to access  
customer calling services that require touch –tone  
dialing ,such as getting information from a local bank  
,you can use this feature.  
Wall plate  
MODULAR JACK REQUIREMENTS  
You need an RJ11C type modular jack, which is  
the most common type of phone jack and might  
look like the one pictured here. If you don’t have  
a modular jack, call your local phone company  
to find out how to get one installed.  
1. Press the TONE button ( * ) after you have connected  
to the service in order to enable touch –tone dialing.  
2. When you hang up, the phone automatically returns  
to Pulse dialing mode.  
Telephone  
line jack  
TONE button  
INSTALLING THE PHONE  
Your telephone should be placed on a level surface such as a desk top,  
or you can mount it on a wall , A desktop /wall mounting pedestal is built  
into the base of the phone.  
MEMORY  
Each of the memory buttons is capable of storing phone numbers that  
are up to 32 digits. Memory locations 0-9 require you to press MEM  
for access.  
STORING A NUMBER IN MEMORY  
1. Pick up the handset.  
2. Press ths STORE button.  
3. Dial the number to be stored (up to 32 digits),  
LCD show the phone number.  
1234567890  
4. Press STORE again.  
5. Press a memory location button(0-9)  
6. Record the telephone number you want to store.  
7. Hang up the handset.  
1. Connect the telephone line cord to a modular telephone jack.  
2. Slide the RINGER switch (on the handset ) to Low or High.  
3. Set PULSE/ TONE switch (on the handset ) to TONE for touch-tone  
service, or set it to PULSE for rotary service. If you don’t know which  
type of service you have, check with the phone company.  
DIALING A NUMBER FROM MEMORY  
You can dial numbers from memory when using the handset. When you  
get a dial tone, press the MEM button followed by the memory location  
(0-9) for the number you want to dial.  
WALL MOUNT INSTALLATION  
INSERTING A P AUSE IN THE DIALING SEQUENCE  
Use the REDIAL button to add pauses to a dialing sequence, for example  
after you dial 9 for an outside line.  
Your telephone may also be mounted on a wall plate (not included).  
1. Slip the mounting holes (on the bottom  
of the base) over the wall plate posts and  
firmly slide the unit down into place.  
2. Plug the telephone line cord into a  
modular wall phone jack.  
TROUBLESHOOTING TIPS  
PROBLEM  
SOLUTION  
No dial tone  
Won’t dial out  
Check hook switch to make sure it pops up.  
Make sure TONE / PULSE is set to correct position.  
INTRODUCTION  
Your Telephone is designed to give you flexibility in use, and high  
quality performance. To get the most from your new telephone, we  
suggest that you take a few minutes right now to read through this  
instruction manual.  
Phone doesn’t ring  
Make sure RINGER switch is set to Hi ( ) or Lo(  
You might have too many phones on one line.  
)
USING THE TELEPHONE FEATURES  
Feedback when  
dialing in PULSE mode  
This is normal, power fluctuates with phone  
outpulsing.  
If you have any questions or problems, consult the Troubleshooting  
Tips for the solution.  
RECEIVING A PHONE CALL  
1. Be sure the RINGER switch is set to Hi (  
) or Lo ( ) position.  
Can’t be heard by  
other party  
Make sure phone cord is securely plugged in.  
Make sure other phones aren’t off the hook  
at the same time you ’ re using the phone.  
It is normal for the volume to drop when  
additional phones are used at the same time.  
2. When the phone rings. lift the handset and begin your conversation.  
3. After 5 sec, a talk timer will be displayed.  
PAPTS CHECKLIST  
Your package should contain the following items:  
4. Slide the RINGER switch to the Off (  
) position when you do not want  
to be interrupted by the phone ringing.  
CARE AND MAINTENANCE  
RINGER VOLUME  
To keep your phone working and looking good ,follow these guidelines;  
You may control the ringer volume level with the switch located on the  
right side of the handset.  
Avoid putting near heating appliances and devices that generate  
electrical noise (for example , motors and fluorescent lamps)  
DO NOT expose to direct sunlight or moisture.  
= ringer tone will be loud.  
= ringer tone will be low.  
Avoid dropping and other rough treatment of the unit.  
Never use a strong cleaning agent or abrasive powder because this  
will damage the finish.  
= telephone will not ring.  
PLACING A PHONE CALL  
1. Lift the handset and wait for a dial tone.  
2. Dial the telephone number you wish to call,  
while the LCD displays ‘Ξ’.  
Retain the original package in case you need to ship it at a later date.  
Base unit with handset  
Used equipment must be disposed of in compliance with  
current environmental protection regulations. You should  
return it to your reseller or dispose of it in an approved  
recycling centre.  
3. After 5 sec, a talk timer will be displayed.  
Ringer  
Hi/Lo/off  
Tone/Pulse  
Switch  
Model EX29268  
00022382 (Rev.0 E/S)  
07-39  
Printed in China  
REDIAL BUTTON  
This unit redials up to 32 digits. To  
automatically redial the last number You  
called:  
Thomson Asia Limited  
3/F., Delta House, 3 On Yiu Street,  
Siu Lek Yuen, Shatin, Hong Kong  
1. Pick up the handset to get a dial tone.  
2. Press redial.  
Store  
Mem  
is a trademark of General Electric Company and is under license by Thomson Asia Ltd., Hong Kong  
Redial  
3. LCD shows the phone number you dialed.  
 

Electro Voice Microphone RE920Tx User Manual
Everpure Water System A 10 User Manual
Fisher Paykel Washer GWLO8 User Manual
Fluke Power Supply 80 Series III User Manual
Furman Sound Power Supply Elite 16 PF E User Manual
Fusionbrands Marine Instruments MS BT200 User Manual
GE Flat Panel Television J2B918BEK User Manual
Gemini Music Mixer UMX SE User Manual
GE Washer Dryer WSM27TH User Manual
Go Video Computer Monitor T2040 User Manual